{"text_format":"3","workbook":"xls","n_sheets":1,"sheets":["2017"],"not_rendered":{"external_links":1},"read":"whole","date_system":"1900","formulas":"cached_only"}

{"sheet":"2017","index":0,"n_rows":89,"n_cols":5,"rows_kept":89,"merged":[[0,0,0,4],[8,1,8,3],[12,2,12,3],[13,2,13,3],[14,2,14,3],[15,2,15,3],[16,2,16,3],[17,1,17,3],[19,1,19,4],[21,2,21,3],[22,2,22,3],[23,2,23,3],[24,2,24,3],[26,1,26,4],[29,1,31,1],[29,2,31,2],[29,3,31,3],[29,4,31,4],[29,5,31,5],[32,1,34,1],[32,2,34,2],[32,3,34,3],[32,4,34,4],[32,5,34,5],[36,1,36,4],[51,1,52,1],[51,4,52,4],[54,1,55,1],[54,4,55,4],[59,1,60,1],[59,4,60,4],[61,1,62,1],[61,4,62,4],[63,1,64,1],[63,4,64,4],[66,1,67,1]],"flags":["formulas_cached_only"]}
["2017车轮定位项目记录单   选手编号：           "]
[]
[null,"一、定位工单流程10作业记录",null,"单位：kpa"]
[null,"项目","调整前","调整后"]
[null,"左前胎压   "]
[null,"右前胎压   "]
[null,"左后胎压   "]
[null,"右后胎压   "]
[null,"轮胎型号是否与车辆铭牌要求一致 是（   ）否（   ）"]
[null,"备注：未作调整的车轮不用记录"]
[]
[null,"车身高度记录",null,"单位：mm"]
[null,"左前P值"]
[null,"右前P值"]
[null,"左后R值"]
[null,"右后R值"]
[null,"车身调平高度最大差值"]
[null,"车身调平高度最大差值是否合格：是（   ）否（   ）"]
[]
[null,"二、定位工单流程16作业记录："]
[null,"轮胎沟槽深度（记录单轮测量最小值）",null,"单位：mm"]
[null,"左前轮胎纹深度"]
[null,"右前轮胎纹深度   "]
[null,"左后轮胎纹深度  "]
[null,"右后轮胎纹深度  "]
[]
[null,"三、定位工单流程49作业记录："]
[null,"(根据实际检测车辆的检测报告勾选填写，仅需在正确项前的□中打√)"]
[null,"项目","数据判断","横拉杆长度\n调整","横拉杆旋转方向调整"]
[null,"左前车轮\n单独前束","□正常合格\n□正向过大\n□负向过大","□无需调整\n□缩短长度\n□伸长长度","□无需调整\n□顺时针方向\n□逆时针方向"]
[]
[]
[null,"右前车轮\n单独前束","□正常合格\n□正向过大\n□负向过大","□无需调整\n□缩短长度\n□伸长长度","□无需调整\n□顺时针方向\n□逆时针方向"]
[]
[]
[]
[null,"别克威朗车身定位分析   选手编号："]
[null,"注：以下题干仅供参考，以实际出题为准，选手现场仅需在ABCD四个选项上勾选。"]
["1、根据你的实际检测报告，对调整前XX数据描述正确的是（单选）。"]
[null,"A、"]
[null,"B、"]
[null,"C、"]
[null,"D、"]
[]
["2、以下针对别克威朗车辆定位角度XXX描述正确的是（多选）"]
[null,"A、 "]
[null,"B、 "]
[null,"C、  "]
[null,"D、  "]
[]
[null,"后轴",null,"调整前检测","外倾角"]
[null,"外倾角","左侧",null,"−1º18′±0º30′"]
[null,null,"右侧"]
[null,"左右外倾角差"]
[null,"单独前束","左侧",null,"0º3′±0º12′"]
[null,null,"右侧"]
[null,"总前束",null,null,"0º6′±0º24′"]
[null,"几何驱动轴线",null,null,"0°00′±0º18′"]
[null,"前轴"]
[null,"主销后倾角","左侧",null,"4°55′±0º45′"]
[null,null,"右侧"]
[null,"主销内倾角","左侧"]
[null,null,"右侧"]
[null,"外倾角","左侧",null,"−0°18′±0º45′"]
[null,null,"右侧"]
[null,"左右外倾角差",null,null,"0°00′±0º48′"]
[null,"单独前束","左侧",null,"0°09′±0°06′"]
[null,null,"右侧",null,"0°09′±0°06′"]
[null,"总前束",null,null,"0°18′±0°12′"]
[null,null,"图表一"]
[]
[]
["3、根据图表一提供XXX测量数据，下列哪项内容不需要检查（单选）"]
[null,"A、 "]
[null,"B、"]
[null,"C、"]
[null,"D、"]
[]
["4、XXXXXXXXXXXXXXX，下列哪些说法正确 (多选)"]
[null,"A、"]
[null,"B、"]
[null,"C、"]
[null,"D、"]
[]
["5、车轮定位XXXX选择正确的一项是（单选）"]
[null,"A、"]
[null,"B、"]
[null,"C、"]
[null,"D、"]